An importer in West Africa asks why two machines from the same container behave so differently: one has run for two years without a call, the other has had three high-pressure trips this summer. Same model, same refrigerant, same operator. In almost every such case the difference was decided on the installation day — by airflow, drainage, electrical supply or the route of a pipe — and none of it appears on the invoice.
The principle: the machine is only half a system
A cube machine is a refrigeration circuit plus a water circuit plus an electrical load, and each of the three depends on the building. The condenser must reject heat into an environment that can absorb it. The water circuit must fill and drain freely. The compressor must receive the voltage and phase it was built for. Get any one of these wrong and the machine will still make ice — badly, expensively and briefly.
The ten mistakes, and what each one looks like
| Mistake | What you will observe | Correct practice |
|---|
| No clearance around the condenser | Output falls in summer, high-pressure trips | Free intake and discharge air, and a route for hot air to leave the room |
| Machine not levelled | Uneven cubes, harvest jams on one side | Level in both axes, shim the feet |
| Wrong voltage, phase or frequency | Overload trips, control board faults | Confirm the nameplate against the site supply on arrival |
| Undersized cable or shared circuit | Nuisance trips when ovens start | Dedicated breaker, cable sized to the nameplate current |
| Drain with no fall | Water pooling, cubes freezing into a block | Continuous fall to drain, no reduction in diameter |
| No air gap at the drain | Odour, contamination risk | Indirect connection to the drainage system |
| Untreated or low-pressure water | Scale, weak fill, short cubes | Filtration plus a stable supply pressure at the inlet |
| Machine placed outdoors without rating | Rain ingress, coil corrosion, solar load | Indoor installation, or an outdoor-rated unit in shade |
| Remote condenser on factory charge | Low capacity, poor oil return | Charge adjusted by weight for the actual line length |
| No commissioning record | Warranty arguments with no baseline | Record pressures, current, cycle and harvest times |
What our own documentation expects
Our cube machines are supplied on 220 V single phase or 380 V three phase depending on capacity: the 60 kg ETD-C120P and the 750 kg ETD-1500P run on 220 V, while the one-tonne series is built on 380 V with Copeland compressors. Refrigerants vary by model and market — R404a, R507a, R134a, R22 — and the charge is set at the factory for the standard configuration. That last point is the one buyers overlook: if you install with a remote condenser and long lines, the charge must be adjusted, and no factory setting survives an unusual pipe run.
Dimensions matter for installation planning as much as for shipping: the mid series is 760 x 830 x 1780 mm, the BMC2000P is 1240 x 950 x 2000 mm, and the one-tonne series is 1300 x 1000 x 1950 mm. A machine that does not fit the alcove with clearances around it will not perform, no matter what the catalogue claims.
Commissioning: the half hour that protects the warranty
- Record ambient and water temperature at the moment of start-up.
- Record suction and discharge pressures after the first full cycle.
- Record compressor current against the nameplate value.
- Time one complete freeze cycle and one harvest.
- Weigh ten cubes and confirm the weight matches the 22 x 22 x 22 mm specification.
- Test the bin drain with a bucket of water and watch it empty.
- Photograph the installation, the nameplate and the drain connection, and file them with the invoice.
That record is what allows a service engineer, two years later, to say whether the machine has changed behaviour or has always run that way. Without it, every discussion becomes an opinion.
FAQ
Can I install it myself? Mechanically, often yes. Electrically and on the refrigerant side, use a qualified technician; the warranty and your insurance both depend on it.
How much clearance is enough? Follow the manual for the model. If the room is small, plan an extraction path rather than relying on the gap behind the machine.
Does a 60 Hz market need a different machine? Yes. Frequency affects motor and compressor speed; confirm it on the order, not on arrival.
What if my supply is 220 V but the model is only offered in 380 V? Choose a model in the 220 V configuration rather than adding a converter; phase conversion is not a reliable long-term solution.
We supply installation and commissioning guidance with every machine, and our engineers will review your site layout before shipment on request. See the 500–1000 kg/24h range, the 4 t/24h industrial unit, or the 1 tonne 380 V Copeland model, or send us your site drawing.
Por favor verifique seu email!